In general, we have decided on the main factors for choosing ankle boots. Elementary care methods were also sorted out. It's time to choose the lacing of the shoulder.
The ankle boots in themselves are quite comfortable shoes, and therefore they went far beyond the army walls, they even began to be preferred by the weak half of humanity. But sometimes during operation, there are difficulties with lacing.
Correct lacing will allow comfort while wearing, when putting on and taking them off, and these are far from secondary factors. Correct lacing methods can be useful not only for military personnel, but also for civilians. The technique differs only from the model and type of laces themselves. Correct lacing will secure the ankle and eliminate the risk of injury.
The lace-up models of the straps differ due to their fixation with eyelets, metal loops, metal blocks or crochet or half rings.
As for the eyelets or blocks, the best option for lacing has become the alternate tightening of crossed pairs, between the metal rings, which takes only one hand.
The simplest version of the Army tie:
- Next, from the inside, the lace is threaded into the following holes
- And so on until the very end
The option is optimal and universal, although it crushes the tongue. To remove, only the upper eyelets need to be released.
Ladder
This method of lacing is used less often, but it fixes the ankle boots on the leg with high quality.
- Both ends of the lace are threaded into the lower eyelets
- We thread one end of the lace into the uppermost eyelet until it is no longer useful to us.
- We thread the free end in the form of a ladder, that is, we thread it into the opposite eyelet and so on to the very top
- Complete the lacing with a comfortable knot at the very top of the boot.
One hand
Convenience is that one hand is freed up and you can feel like a Caesar and play the piano with the other hand.
- We fix one end of the lace in a knot, it remains at the bottom of the first eyelet
- Next, we lace up the ladder in the way to the very end (the difference is only the left and right boots, which, accordingly, the lacing originates either on the left or on the right)
- At the end, we pass the free part of the lace through the entire lacing and hide it so as not to step on it.
Direct hidden
This type of lacing will allow you not to catch, in natural conditions, for tree branches and other factors.
- The laces are threaded at both ends into the bottom holes
- One end is threaded from below into the next eyelet, and the other end through one. All lacing is done parallel to the very end.
We have described the simplest and most popular methods of lacing the bristles, and in order to have something to practice on, we suggest going to the catalog section of the store and choosing the appropriate model of the breeches.
And remember, everything is much simpler than it seems 😉
The skills of how to lace up ankle boots so that it is correct, durable and reliable are useful not only in the army, but also for civilians, especially in extreme situations.
The way how to tie a military boot depends on the type of lacing implemented by the manufacturer in this model - eyelets (holes edged with a metal ring), half rings on a movable loop base, or hooks crowning the top of the boot, with eyelets from the bottom of the vamp.
Each type of lacing has its own way of threading and tightening the laces. The purpose of the optimal lacing method:
- the speed of tightening the laces;
- lightness and simplicity of unlacing;
- reliability and protection against loosening of laces;
- the speed of removing shoes in case of injury.
Each type of lacing has its own rules and tried-and-true secrets so that the ankle boots are secured in an optimal way - fast, light and strong.
How to lace ankle boots with eyelets
Boots with block or eyelets are a classic military version that is still used in many countries for their own armed forces. The traditional knotting with criss-cross laces has been familiar to us since childhood.
But it is not very suitable for the army - in order to lace up the boots in this way, it is necessary to use both hands and alternately tighten each crossed pair from the bottom up, otherwise the fixation will be weak and heterogeneous.
Therefore, for the military, a special option was invented, how to properly lace up ankle boots with eyelets and blocks. 
- First of all, a strong knot is knitted at one end of the lace.
- Threading the lace begins by inserting its free end from the outside of the boot into the lowest hole on the inside of the strip on which the eyelets are attached.
- For the right boot, the beginning will be the bottom of its right edge, for the left - the bottom of the left edge.
- The knot after pulling the rope should remain inside the strip with a hole and be covered with it.
- The lace exit from the eyelet will turn out to be on top of the strip, so the free tip must be threaded into the parallel hole opposite, that is, from the inner edge of the boot, and pulled out from the inside of the strip.
- Now the tip is threaded into the hole above the inner side of the strip and along the same inner edge of the shoe, and is brought out.
- Further, the lacing alternates in this way - to the side to a parallel hole, then up along the same side of the boot. The lace, moving to the side, is threaded in from the outside and stretched inward, and moving upwards, it is threaded in from the inside and stretches out.
- Having reached the last upper eyelet, it is inserted with its free tip from the outside to the inside, but then again it is inserted into the same hole from the inside to the outside, thereby forming a loop on the inside and the tip coming out from the outside.
- The tip must be pulled into a loop and, intercepting the knot in the middle, tighten it. Repeat a series of knots until the end of the lace is short so that it can be hidden and secured by tucking it into the boot shaft or through the unscrewed elastic of the sock.
Shoes tied in this way are unlaced with one sharp pull on the lace at the free end. Further shoeing the ankle boots with such fixation of the laces allows you to tighten them with one finger, while the classic version requires both hands.
By the way! A kind of "pigtail" of knots does not allow the lacing to loosen during long walking, running and jumping.
How to lace up ankle boots on half rings
Movable loops with half rings at the end are good because they already imply high-speed lacing. The fixing cord is loosely tightened and loosened, unlike punched holes - blocks or eyelets. Therefore, the correct option for lacing ankle boots with half rings is a classic criss-cross, since with such loops it loses its shortcomings.
- Free sliding of the lace allows you to firmly tighten the entire lacing, only by pulling the ends of the rope from above.
- There is no need to tighten each block from the bottom up, as is required by ordinary holes, where there is no such free sliding, and where the rope remains relaxed when pulling the adjacent block.
- The same convenience is observed when unlacing - you do not need to stretch each block, it is enough to stretch any block in the middle or at the top to loosen all the fixation.
Note! The end knot can be any, but one should take into account the multiple complaints about such ankle boots due to the weakening of the tightening over time. Experienced fighters advise to make the girth of the bootleg with a cord - this will make the fixation stronger and more reliable, and the dangling ends of the rope will be shorter. If a loop is sewn on the back of the bootleg, it is advisable to pull the laces through it.
How to lace up ankle boots with hooks
Ankle boots with eyelets with hooks on the top of the bootleg are also included in the shoes with high-speed lacing. But not everyone understands how to lace up ankle boots with hooks so that it is really fast.
The secret to hooks is simple.
- The boots are laced crosswise in the traditional way.
- They are tightened, thrown over the hooks at the top and fixed with a knot only the first time.
- To take off the shoes, the knot is not untied, but part of the lacing is thrown off the hooks, then the tightening is relaxed.
- In order to fix the rope again after putting on the ankle boots, the lacing is pulled up and the free part, tied, is again thrown onto the hooks.
Note! This method is not suitable for intercepting the bootleg with a lace, so anyone who needs such additional fixation loses all the advantages of high-speed lacing.
Ankle boots are an extremely comfortable type of footwear that can be used both in autumn and winter. The relatively low weight of these shoes is another advantage that is almost impossible to level with anything. These shoes can be called both stylish and extremely practical. It will be the perfect choice for those who would like to purchase the most versatile wardrobe item as possible.
However, ankle boots have one drawback. Over time, this disadvantage may not be noticed, however, this will require mastering a relatively difficult skill. The point is that it takes a long time to lace up the ankle boots, and most importantly, it is difficult. It will be extremely difficult for an unprepared person to cope with this task. It is for this reason that it is so important to master this skill as soon as possible. In this case, these shoes will be the perfect solution for any time of the year.
There are many reasons for properly lacing ankle boots.
Finding the most suitable lace length can be a daunting task for the vast majority of people who buy such shoes for the first time.
- It is recommended that you choose laces with someone who has done this before. In this case, someone else's experience will come in handy. Also, your best bet would be to try to study the length of your old laces. If such an opportunity is completely absent, then you will have to rely on the opinion of the consultant of the store where the boots were bought. He must have this information.
- Despite the fact that there is a lot of information on this matter on the Internet, it is best to trust people who have already worn such shoes. They will be able to give much more valuable advice.
IMPORTANT! The total length of laces that may be required for such shoes is directly related to the number of holes. Most often, on the open spaces of the Runet, you can find information that in the case of two pairs of eyelets, laces will be required, whose length reaches 45 cm.If we are talking about 3-4 pairs of holes, then laces 60 cm long will be required and so on.
Today laces are made from a wide variety of materials, including leather, jute, and cotton. When choosing laces, you need to focus on your own needs. It is possible that the buyer of such products is a purely domestic person who does not need any additional advantages of materials that can withstand extreme operating conditions. In this case, it is recommended to choose laces that are stylish and modern in appearance.
Schemes of how to lace up special forces ankle boots
The lacing process in this case is quite simple. First, you need to thread a couple of ends through the holes that are on the bottom of the shoe. After that, it remains to insert the ends of the laces into the eyelets. They are located opposite. This completes the lacing process.
The most popular type of lacing is army lacing. There are many reasons for this. In particular, in this way you can tie your laces as quickly as possible.
- First, you need to thread the laces through a couple of holes located on the bottom.
- After that, you need to cross the ends, and then thread them into another row of loops. Since in this case it is the speed that is important, then, obviously, at the first opportunity, you need to tie the laces in any other way.
This method was developed especially for those who need speed. This type of lacing is called "army" for a reason. With its help, a soldier will be able to put on his shoes in a matter of seconds, after which he will be absolutely ready for any combat mission. That is why this type of lacing is called army lacing.
Quick lacing ankle boots
This option is suitable both for emergencies and for those people who just like to save time.
Attention! At the very last hole, it is required from the outside to insert the lace inside the eyelet, and then immediately bring it back out, making a loop in this way. You can thread the free end into it. Then the knot is tightened in the very middle.
Ladder lacing
Also today "ladder" lacing is very popular. It also has one more name - "European". Shoes that have been laced up like this look very neat. To do this, you just need to pass 1 lace through the holes that are on the bottom. After that, it remains to bring the lace out from all ends.
Even a schoolchild can cope with this task, so the "ladder" lacing method is often practiced in camps for teenagers. There, children are taught a wide variety of skills that can only be useful to them in real life. One such skill is the ability to tie ankle boots. The "ladder" method can be called ingenious, because in this way you can not only save a lot of time and effort, but also effectively tie the laces on your own shoes.
If we are talking about rough terrain or some other difficult conditions, then it is best to lace up the ankle boots differently than usual. In this case, the laces will not cling to grass, driftwood, and branches. What needs to be done in order to realize everything that has been conceived? First you need to thread the ends of the laces through the lowest holes. When this is done, all that remains is to tuck one of them into the next, which is all on the same side. Then you need to change sides and continue lacing in the same way.
Recently, ankle boots have become more and more popular. They can be combined with a wide variety of items, so they can be used in almost any wardrobe.
INTERESTING FACT. Most often, ankle boots are needed in order to emphasize the masculinity of a suit. Interestingly, girls often use this element.
They will make their owner much more attractive in the eyes of women, because such shoes fit even jeans and look very masculine. Usually, buyers prefer those models that have a universal color. In this case, these shoes can be worn almost at any time of the year, except for autumn.
How beautiful to tie ankle boots
This method is extremely simple.
- First, you need to take the lace and try to stretch it literally through all the holes that are in the bottom of the shoe.
- After that, the ends must be crossed among themselves and threaded into other holes (we are talking about the upper part of the shoe). Then you get a stylish lacing that will emphasize all the advantages of this shoe.
Where to put the rest of the laces
Many people think that the easiest way is to use the last hole in the row. Then you just need to insert the ends of the laces inward, not outward. In this case, after the laces are tied, the ends of the bow will be located so that they can be threaded through the "tongue".
To know how to lace up ankle boots correctly, you need to understand what it is for. Reliable fixation allows the ankle to take the ideal position, avoid injuries, excessive stress. Also, the lacing should provide a quick release of the boot or a change in tension.
Universal ways of lacing ankle boots with eyelets
Military and special forces from different countries know how to properly tie the laces on their ankle boots with eyelets or blocks (holes with a metal sleeve). Therefore, their experience is successfully adopted by ordinary owners of high boots in summer and winter versions. The statutory options of the Israeli, British, American armies are not always spelled out in the instructions, which leaves the freedom of choice in the service.
Army
One of the most popular methods - "army", is convenient for its speed and the ability to adjust the tension:
- Both ends of the laces are threaded into the bottom holes at the top.
- Then, from the inside, they are inserted into the next eyelets opposite.
- Continue to the end.
The army version has one drawback: the tongue is crushed strongly. Advantage: you do not need to completely untie each time when taking off your shoes, just remove the laces from the upper pairs of eyelets. Also suitable for ankle boots with loops.
Ladder
Ladder lacing is not so common, but it very reliably fixes the ankle boots on the leg in the correct position:
- The first step is the same as in the army method.
- Insert one end into the uppermost eyelet on the opposite side and leave it alone.
- The other is threaded obliquely into the second hole, from below it is inserted into the opposite one.
- Repeat to the end.
- When you get the ladder, as in the picture, tie both ends of the cord into a knot.
From the outside, the result looks very nice and neat.
With one hand
An interesting way is one-handed lacing. The name already promises an additional benefit: it frees one hand, for example, if it is injured. You need to tie in this way according to the following scheme:
- A knot is tied at the end of the lace.
- The cord is threaded into the bottom hole from the inside (for the left tibia in the left corner, for the right by analogy) until it stops.
- The knot should be hidden behind a strip of leather or waterproof fabric with eyelets.
- Then it is passed through the hole opposite.
- From the inside, they are threaded diagonally into the eyelet.
- Continue to lace up as described above.
- The free part of the lace is tucked under the lacing so as not to step on it.
Diagonal "lines" should be formed inside.
Hidden straight
For rough terrain and other difficult conditions, it is appropriate to lace up ankle boots with blocks in a "hidden" straight way. Advantages: the lace does not cling to branches and snags. The implementation of the method consists in the following actions:
- The ends of the cord are threaded through the bottom holes.
- One of them is tucked into the next on the same side, and the second through one.
- Change sides and continue to lace up according to the same principle.
The picture below shows a diagram of how to properly tie the laces on the ankle boots in a "hidden" direct way.
Secure lacing of ankle boots with hooks
In this case, the traditional "criss-cross" method is suitable:
- The lace is threaded from the inside through both lower hooks.
- Each end is wound obliquely behind the fasteners.
Convenient and easy option, you can save time with it. At the same time, the tongue is crushed more than with other methods, but the ankle is securely fixed.
The traditional pattern for ankle boots with this fastening is suitable for those who often have to take them off or change the tension. To do this, it is enough to remove the lace from 2-3 upper hooks, and loosen on the lower ones. In the process of wearing, they will not loosen and press excessively on the leg.
Lacing ankle boots with loops
For ankle boots with loops, there are little tricks, for example, for D-rings, it is important to make knots at the ends of the laces. Such boots are used in the army and simply in the field due to the fact that the loops do not cling to branches, grass and clothing when squatting. They are also in demand in the Airborne Forces, like shoes with eyelets, and in the special forces of different countries. The hidden method is not suitable due to the fact that the cord is not tucked inside. Boots with loops are widely represented in the lines of modern brands: in the USA they are the world famous Timberland, Columbia. Ankle boots with this fastening are laced in universal ways:
- army;
- ladder.
Loops allow you to lace up the ankle boots very quickly, relax or increase their tension, and adjust the tongue, which saves time. It is important to use all the fasteners provided by the manufacturer, often tactical shoes have fasteners on the upper part so that it does not dangle on the leg. It is better to tie up landing boots with a soft, shock-absorbing sole and specially hide the loose ends after you have finished lacing. Craftsmen advise to make additional fastenings on the back of the ankle boots in the form of a loop or ring, where the model allows and the cord will be fixed.
The video shows how to lace up ankle boots and other high shoes with loops and hooks. Helpful tips for beginners.
How to choose the right laces for ankle boots
Usually, army ankle boots or branded shoes, such as Timberland, or one or more pairs of laces are attached. However, many of them change to new ones, choosing the material, color or length for individual parameters. Soft leather laces are the best way out if you have to often visit the area of water bodies or during precipitation in open areas. It is important if there is a risk of suddenly being at a depth and you need to quickly get rid of shoes so that they do not interfere with swimming. They are easy to remove in a few minutes wherever you need it.
Double-braided Kevlar laces are also moisture resistant when soaked in a special synthetic material. Under the influence of moisture, they lose no more than 15% of their strength. And this is important for the correct fixation of the ankle during active movement and the impossibility of constantly tying the laces on the tibia.
Calculating the length of laces for any shoe
A separate issue is the choice of length for the correct lacing of boots and ankle boots. It all depends on the height of the bootleg. There is a formula for calculating the approximate lace length as shown below:
Horizontal distance (in mm) × Number of eyelets + 500 mm
Calculation example
On the boot of a typical model with a hole width of 50 mm and six pairs of eyelets (12 in total), the approximate length of the lace is as follows:
50 mm × 12 (eyelets) + 500 mm = 1,100 mm (110 cm).
Looped shoes
For shoes with loops instead of eyelets, add the width of the hole to the measurement of the horizontal distance between them. For example, on a standard bootleg with a width of 50 mm between holes and five pairs of loops (10 in total), each about 8 mm wide, the approximate length of the lace is:
50 + 8 = 58 mm, × 10 (hinges) = 580 mm, + 500 mm = 1080 mm (108 cm).
Shoes with eyelets and loops
Finally, for shoes with eyelets and loops, add the proportion of the eyelet width to the horizontal distance measurement. For example, a bootleg may have 2 pairs of holes and 6 pairs of loops for a total of 8 pairs of "holes". This means 3/4 of the total number of stitches, so only 3/4 of the width needs to be added. With a horizontal spacing of 50mm and a grommet width of 8mm, we would add 3/4 of the grommet width (6mm). The approximate length of the laces will be:
50 + 6 = 56mm, × 16 (holes) = 896mm, + 500mm = 1.396mm (140cm).
Many experienced high shoe owners note that it is more practical to use laces a few centimeters longer than standard laces. Then they can be tied in different ways, and the ends can be hidden inside the shoe or in another way. Laces for military ankle boots come in different colors, common: khaki, black, brown, two-tone
Lacing ankle boots for different activities
In England and other European countries, as well as in the United States, samples of footwear for the military are similar depending on the purpose. It depends on the model how to properly lace up the ankle boots. If they are used only in everyday life, then you can choose one of the lacing methods and tie them, following any photo with descriptions. With increased loads on the ankle, you should pay attention to the methods described above for several attachment options, as additional protection from injury and inconvenience.
Video instruction for lacing high boots with loops in an army way. Locking the risers to the shaft.
For reading 9 min. Views 3.1k.
Ankle boots - boots with a high reinforced bootleg and lacing. This is one of the main elements of military equipment in almost all countries. Shoes are lightweight, retain heat well, do not allow moisture to pass through, and are extremely comfortable when walking long distances. The ankle in such boots remains mobile, but at the same time it is securely fixed, but for this you need to know how to lace up the ankle boots, doing it correctly and quickly. Due to their characteristics, these boots are widespread among the civilian population - especially among tourists and extreme sports enthusiasts.
Specificity and basic rules
The lacing of the ankle boots is one of the most important elements of this type of footwear. The comfort of their owner and how much distance he can overcome depends on how correctly it is made. Knowing how to properly lace up ankle boots is very important for the following reasons:
- improper lacing of the ankle boots can impede the free movement of blood;
- if the leg is not securely fixed, the risk of injury or sprain increases greatly;
- the lacing should be such that the boots can be quickly removed or put on;
- in poorly tightened shoes, the leg gets tired faster, calluses may appear where they could have been avoided;
- if the lacing is done incorrectly, it can loosen or completely untie at the most inopportune moment, and in difficult terrain it is very traumatic.
It is best to lace up boots immediately on the foot, this will allow you to tighten the string as tightly and comfortably as possible. When removing a boot, it is not necessary to unlace it completely - it is enough to loosen the top row so that it can be easily removed, and then put on the foot just as easily and quickly.
Anyone who needs to wear these boots should know how to lace up the ankle boots to avoid injury and to make these boots as comfortable and comfortable as possible.
Rules for choosing the length and material of laces
Laces are the most important and also the most vulnerable element of the ankle boots. Most often, such shoes are used in extreme conditions, so the laces quickly fray or rot, risking unexpectedly bursting. Increased requirements are put forward for this element, because the laces on the ankle boots should always be in excellent condition so as not to let down their owner.
The material must be strong, durable. Now laces for ankle boots are made of rope, cotton or synthetics. Harness, cotton are cheaper, but their service life is much shorter. Synthetics are more resistant to wear and tear, they will last much longer.
Kevlar laces with a nylon braid have the greatest strength. Kevlar threads are incredibly durable. They are used in the production of body armor, since it is this material that can withstand bullets.
The length of the laces is also an important factor. If they are too short, it will be impossible to properly lace up the ankle boots, too long are uncomfortable.
The length is chosen depending on the number of pairs of eyelets or hooks. Manufacturers have developed a standard scale:
- 6-8 pairs - 90-100 cm;
- 8-10 pairs - 120-124 cm;
- 10-12 pairs - 180 cm;
- 12 pairs or more - 220 cm.
Laces that are too long, up to 220 cm, can be used for purely practical purposes. Due to the high strength of the material, if necessary, it can be cut in half and one half laced the boot, and the other used as a reliable rope. Even the shape of the army laces can affect the comfort of wearing ankle boots. Flat ones less squeeze the leg even with tight lacing, while round ones are more durable and comfortable to use. Here the choice depends entirely on personal preference and habits.
Laces for ankle boots 
Kevlar for military ankle boots Lacing patterns
There are many different ways to lacing ankle boots, each with its own advantages. Different countries and divisions of the army use different techniques - it all depends on the activity and environmental conditions.
Army-style
Army lacing is the most common pattern used by special forces and military personnel. Its advantage is that it is easy to tighten and adjust. Thanks to this technique, the boot can be easily removed by quickly relaxing the upper part, just as easily put back on in a matter of seconds.
The lacing technique is as follows:
- Take both ends and slide them into the lowest holes from outside to inside. Thus, a crossbar is formed between the initial holes, which will be the middle of the lace and divide it in two.
- Climb into the next highest holes by inserting the left end of the lace from the inside out into the left hole, and the right end into the right one.
- Now both ends come out. You need to cross them and climb to the next highest pair of holes. Thus, the left lace will go from the outside to the inside into the right hole, and the right lace will go into the left.
- Both laces are inside again, so you can repeat everything as in the second step. Climb the next pair of holes without crossing, the left lace will come out through the left hole, and the right lace through the right one.
- Repeat the crossing as in the third step and climb one more pair of holes.
Thus, you need to continue to the very top of the boot. The military lacing technique allows you to quickly take off and then put on your boots during a halt or loosen the laces if you need to fix something right during the hike.
Fast
In extreme conditions, it is important to know how to lace up the ankle boots if one hand is injured. You can use a simple, quick method. With this technique, you can actually tie your shoelaces using just one hand.
The technique is as follows:
- At one end of the lace you need to tie a strong knot, and thread the other into the left (for the left tibia) and right (for the right) hole in the lowest row. Then pull it out completely until it stops so that the knot rests against the hole from the inside.
- The remaining end must be threaded into the opposite hole from the outside to the inside (you get a horizontal bar).
- Pull the lace obliquely and thread it into the opposite hole of the next highest row from the inside out.
- Repeat step two to create a second bar parallel to the first. Then repeat the third step and so on until the very end.
The remaining end of the lace must be tightened, securely hidden. There is another option for tightening, when the second end of the lace is not tied in a knot, but is initially pulled into the hole in the uppermost row. Then, when the other end gets to the top, they tie and hide.
Ladder
This method is less common, but it helps to securely fix the leg.
The technique consists of the following steps:
- The first step is to thread the lace through the pair of bottom eyelets to form the first crossbar.
- Next, push the right end into the right hole of the next highest row from the outside to the inside, and the left into the left (in this case, two vertical crossbars are formed between the first and second rows on the left and right).
- Cross both ends of the lace. The left end must be pulled under the right vertical bar and inserted into the right hole of the next highest row from outside to inside. Pull the right end under the left vertical crossbar and insert it into the left hole of the next row. This will create two more vertical beams.
- Next, cross both ends of the lace again and repeat the previous step.
The result is a neat, secure, well-adjustable lacing that is a series of horizontal rungs that resemble a rope ladder.
Hidden line
This method is good for cross-country hikes. With such a lacing, the risk of catching on snags or branches and getting injured is reduced.
The technique is as follows:
- The lace is pulled through the two lowest eyelets and divided into two equal parts.
- The right end must be pushed into the right hole of the next highest row from the inside out. The left one goes into the left hole of the third highest row, skipping the second.
- The end of the lace coming out of the right hole of the second highest row must be pushed into the left hole of the same row from outside to inside. You will get another crossbar, parallel to the initial one.
- The end coming out of the left hole of the third highest row must be pushed into the right hole of the same row from outside to inside. You will get one more, third crossbar, parallel to the first previous two.
- Then repeat everything again as in step 2, then steps 3 and 4, continue this way until the very end.
This is a pretty simple, practical technique. At the same time, the lacing looks very neat, minimalistic. It is convenient in an emergency. For example, if a leg is injured, a healthcare professional can quickly cut the lacing in one motion.
It is important to fully tie the laces on the ankle boots, as loose ends that are not tucked in will get in the way and could result in injury. Both ends are securely tied to each other, hidden inside the boot or threaded under the tongue.
Creative
Many men prefer ankle boots for everyday wear, making such boots an integral part of their image. Then different lacing patterns are no longer used for practical, but purely aesthetic purposes. There are many ways to lace up ankle boots beautifully, from simple combinations of different colors to complex patterns (lattices, stars). It all depends on the imagination, the skills of the mod.
The choice of the scheme depending on the design and height
Each scheme is good in its own way and is chosen depending on how quickly you need to lace up or unlace the boots, what the boots are equipped with (eyelets, half rings or loops), what their height is. If you need to put on or take off your boots as quickly as possible (especially important for soldiers), then it is best to choose a simple technique.
The fastest is the lacing of the ankle boots with hooks. In this case, it is best to use military equipment or the most ordinary criss-cross lacing.
When you have to overcome a long way over rough terrain, you need to know how to properly lace up the ankle boots so that the leg is securely and safely fixed, and the laces do not interfere while walking. The "ladder" method is suitable for this. Civilians can use any kind of lacing they want - all options are suitable for everyday life.
With eyelets 
With hooks Video
